Coverage Maps

Live public maps of mesh and amateur radio nodes, centered on Cache Valley.

About these maps

Cache Valley Mesh does not publish its own coverage map. Each map below is run by a third party, and we link to it, or load it on request, centered on Logan at about 41.73° N, 111.83° W.

What a dot on a map means: a node reported a location to that map at some point. It does not mean the node is on the air today, and it does not mean your radio can reach it.

  1. Coverage shown on this page comes only from the third-party sources named on each card.
  2. Maps can be incomplete, out of date, or include nodes that have moved or gone offline.
  3. Embedded maps load only when you select Show the map here, so this page does not contact those sites until you ask.

MeshCore

MeshCore Node Map

What it shows: MeshCore companions, repeaters, room servers, and sensors whose adverts were uploaded to the map, with filters for node type and how recently each node was heard.

Limits: Entries are uploaded by operators, so nodes can be stale, misplaced, or missing. The map also has a coverage estimate tool that models terrain. That is a prediction, not measured coverage.

Source: map.meshcore.io (opens in a new tab). Map data and attribution belong to that site.

Meshtastic

Meshtastic Map by Liam Cottle

What it shows: Meshtastic nodes that sent a valid position to the map's MQTT server, either directly or through a node that heard them and uplinks to that server.

Limits: Nodes that never reach that MQTT server, or that encrypt position with a private key, do not appear. The map undercounts the local mesh, especially radios that are off the internet.

Source: meshtastic.liamcottle.net (opens in a new tab). Map data and attribution belong to that site.

AREDN

AREDN World Map

What it shows: AREDN nodes that the project's mapper can reach through the supernode network, with band and channel filters and each node's last-seen time.

Limits: Nodes that are not linked to a mapped network do not appear, and nodes can stay listed for a while after they go offline. Our AREDN page explains that we have not verified a current Cache Valley AREDN node list.

Source: worldmap.arednmesh.org (opens in a new tab). Map data and attribution belong to that site.

APRS

aprs.fi

What it shows: Live APRS positions, weather stations, digipeaters, and iGates that reached the internet APRS-IS network.

Limits: Only packets heard by an iGate appear. A station that is on the air but out of iGate range will not show up.

Source: aprs.fi (opens in a new tab). Map data and attribution belong to that site.

AllStar

No coverage map

AllStar links repeaters and nodes over the internet, so its local coverage is the radio coverage of each linked repeater. We know of no public coverage map for the Cache Valley node. The AllStar page lists node 52787 on the AC7O 147.200 MHz repeater at Smithfield Fire Station, as published by BARC.

Live status: AllStarLink stats for node 52787 (opens in a new tab).

HaLow

No public map yet

We have not found a public Wi-Fi HaLow deployment or map for Cache Valley. If you run a HaLow link in the valley and can share a public write-up, the HaLow page explains what we would cite.

Put your node on the map

These maps only know about nodes that report to them. If you run a node in Cache Valley, adding it helps everyone see where the mesh reaches.

  1. MeshCore: follow the instructions on the MeshCore Node Map (opens in a new tab), and register a rooftop repeater (opens in a new tab) with MountainWest Mesh (opens in a new tab). The MeshCore getting started guide covers the local settings.
  2. Meshtastic: the Liam Cottle map lists nodes heard on its MQTT server. Its help screen asks for an MQTT uplink, a position that is unencrypted or uses the default key, and, on firmware 2.5 or newer, the “OK to MQTT” setting. Use MQTT only if you are comfortable sharing that data publicly.
  3. AREDN: set your node’s location, then link it by RF, device-to-device, or a tunnel to a network the AREDN mapper already reaches. Members of the AREDN forum describe the map as network based (AREDN forum (opens in a new tab)).
  4. APRS: beacon on 144.390 MHz. Packets that an iGate hears appear on aprs.fi automatically.
  5. Tell us: if a public map or a documented local node is missing from this page, contact us with a link we can cite.
  6. Tell the community: the Freq51 Discord (opens in a new tab) has regional onboarding and separate Meshtastic and MeshCore channels.

Each map’s terms and privacy practices are its own. Read them before you share a home location.